SPECIFICATIONS – Vehicle mounted: Model cx
Up to 1500 GPM (6000 l/min) Flow Performance
The CX single-stage end-suction pump provides reliable performance from 750 GPM @ 150 PSI (3000 L/min @ 10 bar) and up to 1500 GPM @ 150 PSI (6000 L/min @ 10 bar).
CX Pump PerformanceGPM / l/min / l/sec / PSI / bar / kPa / MPa
750 / 3000 / 50 / 150 / 10 / 1000 / 1.0
1000 / 4000 / 65 / 150 / 10 / 1000 / 1.0
1250 / 5000 / 80 / 150 / 10 / 1000 / 1.0
1500 / 6000 / 100 / 150 / 10 / 1000 / 1.0
Pump Features
Ó 2014 Waterous Company 125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA F-2095
www.waterousco.com Specifications subject to change without notice. Revised: 05/21/14
SPECIFICATIONS - PTO Driven: Model CX
Pump Transmissions
Ó 2014 Waterous Company 125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA F-2095
www.waterousco.com Specifications subject to change without notice. Revised: 05/21/14
Ó 2014 Waterous Company 125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA F-2095
www.waterousco.com Specifications subject to change without notice. Revised: 05/21/14
K Series
The K Series Transmission is normally used when a truck transmission mounted power take-off is selected as the pump drive.
Housing: Close-grained, gray iron
Gears: Helical, precision cut, crown shaved for proper load distribution and quiet operation.
T Series
The T Series Transmission is supplied when the pump is to be mounted directly to the engine bell housing. This provides a clean, compact arrangement and allows for complete pump and roll capability.
T Transmissions are available in SAE 2, 3, 4, or 5 bell housing adapters.
Housing: Close-grained, gray iron
Gears: Helical, precision cut, crown shaved for proper load distribution and quiet operation.
D Series Direct Drive
Used when a truck transmission mounted power take-off is selected as the pump drive.
Housing: High-strength aluminum
C20 Series
The “C20” series transmission is supplied when the pump is to be midship mounted. Power from the truck's automatic transmission is transmitted to the pump.
Housing: High-strength aluminum
Chain: Morse HV®, high-strength involute chain
PA Series
PA Series transmission is normally used when a truck transmission mounted power take-off is selected as the pump drive. Designed for use with Allison transmissions with 10-bolt PTO.
Housing: High-strength aluminum
Chain: Morse HV®, high-strength involute chain
QB Series (CXV Pumps Only)
QB Series transmission is normally used when a truck transmission mounted power take-off is selected as the pump drive. Designed with an 18-1/4” offset.
§ Chain Driven
§ Aluminum Case
§ 1:06 ratio
§ 1.750-10 SAE spline with SPL Series 90 End Yoke
Ó 2014 Waterous Company 125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA F-2095
www.waterousco.com Specifications subject to change without notice. Revised: 05/21/14
Accessories & Optional Equipment
Ó 2014 Waterous Company 125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA F-2095
www.waterousco.com Specifications subject to change without notice. Revised: 05/21/14
The accessories below are available for Waterous CX pumps. For detailed information about these accessories, request each specification sheet by number.
Primer
Select an electric rotary vane primer for fast, reliable priming. F-2418
Pressure Control Systems
Discharge Relief Valve
Simple ON-OFF control permits placing the system in or out of operation in seconds. See Relief Valve, F-897.
Intake Relief Valves
The Waterous intake relief valve is designed to dump excess pressure from the inlet side of the pump. See Intake Relief Valves, F-2192.
Corrosion Protection
Waterous offers replaceable zinc intake screens and anodes to provide corrosion protection. These items are designed to sacrifice the zinc element to galvanic corrosion. Without this protection, galvanic corrosion may damage the iron pump body and fittings.
Overheat Protection Manager
The OPM consists of an illuminated warning light on the operator's panel whenever the pump approaches an overheat condition. F-2422
Drain Valves
Drains all points of the pump simultaneously with the operation of a single control. F-1158
Discharge Valves
The following Waterous ball-type discharge valves are available: 2-1/2 inch, 3-1/2 inch, rack and sector push-pull, worm gear and electric. Chrome- plated brass ball and hydraulically-balanced seal assembly standard. See Discharge Valves, F-1161.
Tachometer
Tachometer drive available; operates at 1/2 input shaft speed.
Five-Year Limited Warranty with Total Protection Package (TPP-5)
The Five-Year Limited Warrant with Total Protection Package is a comprehensive warranty that increases your standard warranty to include labor expenses to dismantle, remove and reinstall covered products or parts, F-2626.
Intake Connection:
Type / Model / SizesVictaulicÒ Intake / CXV / 6 inch
Rams Horn Dual Intake / CXS / 6 inch
Flange / CXN / DIN PN10 150
Note: 6 inch threaded intake available with 3 inch auxiliary intake ports.
Ó 2014 Waterous Company 125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA F-2095
www.waterousco.com Specifications subject to change without notice. Revised: 05/21/14