Preliminary

P/N：PO-TS3014WWSN-D01(0.2W)

CUSTOMER
APPROVED
SIGNATURES / APPROVED BY / CHECKED BY / PREPARED BY

Device To Amend Note

Rev. / To Amend Date / Device To Amend Content / Notes
1.0 / 2014.09.12 / 新制定
New design

■Features

  1. High Luminous Output
  2. RoHs Compliant and Pb Free
  3. Silicone Encapsulation
  4. Energy Star / ANSI compliant binning structure

■Application

  1. Down light
  2. PAR light
  3. Spot light
  4. General lighting
  5. Architectural lighting

■Absolute Maximum Ratings

（Ta=25℃）

Parameter / Symbol / Rating / Unit
Power Dissipation / PD / 270 / mW
Forward Current (DC) / IF / 75 / mA
Peak Forward Current
(Pulse width ≦ 0.1msec. duty ≦ 1/10) / IFP / 100 / mA
Reverse Voltage / VR / 5 / V
Electrostatic Discharge(HBM) / ESD / 1000 / V
Operating Temperature / Topr / -40 ~ +85 / ℃
Storage Temperature / Tstg / -40 ~ +100 / ℃
Soldering Temperature / Tsld / Reflow Soldering:260℃/10sec
Hand Soldering:350℃/3sec

■Package Dimensions

Unit:mm

Note: General Tolerance of the Package dimension ±0.1mm

■Optical Characteristics

（Ta=25℃）

Parameter / Symbol / Min. / Typ. / Max. / Unit / Test Condition
Luminous Flux / Φv / 17.5 / / / 32.5 / lm / IF=60mA
Forward Voltage / VF / 2.9 / / / 3.6 / V
Viewing Angle / 2θ1/2 / / / 120 / / / Deg
Color Rendering Index / Ra / 80 / / / / / %
Reverse Current / Ir / / / / / 5 / μA / VR=5V

Note:

  1. Maintains a tolerance of ±10% on Luminous Flux measurements.
  2. Maintains a tester tolerance of ± 0.1V on forward voltage measurements.
  3. Parts are tested in pulsed conditions, Pulse width is 10 ms at rated test current.

■Luminous Flux Bin Table

Bin Code / Min / Max / Unit / Condition
L04B / 17.5 / 20 / lm / IF=60mA
L05A / 20 / 22.5
L05B / 22.5 / 25
L06A / 25 / 27.5
L06B / 27.5 / 30
L07A / 30 / 32.5

Note: Tolerance of the Luminous Intensity ±10%

■Forward Voltage Bin Table

Bin Code / Min / Max / Unit / Condition
H1 / 2.9 / 3.0 / v / IF=60mA
H2 / 3.0 / 3.1
I1 / 3.1 / 3.2
I2 / 3.2 / 3.3
J1 / 3.3 / 3.4
J2 / 3.4 / 3.5
J3 / 3.5 / 3.6

Note: Tolerance of the Forward Voltage ±0.1V

■ANSI Chromaticity Bin Table

Warm White BIN Structure

Bin code / CIE-x / CIE-y / Bin code / CIE-x / CIE-y / Bin code / CIE-x / CIE-y
35A / 0.3889 / 0.3690 / 30A / 0.4147 / 0.3814 / 27A / 0.4373 / 0.3893
0.3943 / 0.3853 / 0.4223 / 0.3990 / 0.4468 / 0.4077
0.4083 / 0.3921 / 0.4345 / 0.4033 / 0.4578 / 0.4104
0.4018 / 0.3752 / 0.4260 / 0.3854 / 0.4483 / 0.3919
35B / 0.3943 / 0.3853 / 30B / 0.4223 / 0.3990 / 27B / 0.4468 / 0.4077
0.3996 / 0.4015 / 0.4299 / 0.4165 / 0.4562 / 0.4260
0.4148 / 0.4090 / 0.4431 / 0.4213 / 0.4688 / 0.4290
0.4083 / 0.3921 / 0.4345 / 0.4033 / 0.4578 / 0.4104
35C / 0.4083 / 0.3921 / 30C / 0.4345 / 0.4033 / 27C / 0.4578 / 0.4104
0.4148 / 0.4090 / 0.4431 / 0.4213 / 0.4688 / 0.4290
0.4299 / 0.4165 / 0.4562 / 0.4260 / 0.4813 / 0.4319
0.4223 / 0.3990 / 0.4468 / 0.4077 / 0.4703 / 0.4132
35D / 0.4018 / 0.3752 / 30D / 0.4260 / 0.3854 / 27D / 0.4483 / 0.3919
0.4083 / 0.3921 / 0.4345 / 0.4033 / 0.4578 / 0.4104
0.4223 / 0.3990 / 0.4468 / 0.4077 / 0.4703 / 0.4132
0.4147 / 0.3814 / 0.4373 / 0.3893 / 0.4593 / 0.3944

■Typical Electro-Optical-Thermal Characteristics Curves

■Taping Dimension (unit= mm)

Tolerance: ±0.2 (unit= mm)

Quantity: 2000 pcs/Reel

■Label Explanation

BIN CODE: xxx-xxx-xxx

a b c

a: Flux(lm)

b: VF(V)

C: Chromaticity Bin

■Packing(unit= mm)

1. Anti-Static Reel in 1 Moisture proof Foil Bag.

(Within Moisture Absorbent Material)

2.Moisture proof Foil Bag in 1 Inner Box.

3.Inner Box in 1 Carton.

■Soldering

(1)Lead-Free Solder

Lead Free Solder
Pre-heat / 150~200°C
Pre-heat time / 120 sec. Max.
Peak-Temperature / 260°C Max.
Soldering time Condition / 10 sec. Max.

(2)Hand Soldering conditions

Do not exceed 3 seconds at maximum 350°C under soldering iron.

(3)The encapsulated material of the LEDs is Silicone.

(4)Reflow soldering should not be done more than two times.

(5)When soldering, do not put stress on the LEDs during heating.

(6)After soldering, do not warp the circuit board.

■Precaution for use

  1. Storage

In order to avoid the absorption of moisture, it is recommended to store in a dry box (or a desicator) with a desiccant. Otherwise, to store them in the following environment is recommended.

Temperature: 5℃~30℃ Humidity: maximum 70%RH

  1. Attention after open.

LED is correspond to SMD, when LED be soldered dip, interfacial separation may affect the light transmission efficiency, causing the light intensity to drop. Attention in followed; Keeping of a fraction Temperature: : 5℃~40℃ Humidity: less than 10%

  1. Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable,

a double-head soldering iron should be used.(as below figure) It should be confirmed beforehand

whether the characteristics of the LEDs will or will not be damaged by repairing.

■Static Electricity

  1. Static electricity or surge voltage damages the LEDs.

It is recommended that a wrist band or an anti-electrostatic glove be used when handing the LEDs.

  1. All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs.

Rev: 1.0 / Part No. PO-TS3014WWSN-D01-0.2W / Update 2014/09/12 / Page / 1OF 12