P2172-HIGH AIRFLOW/VACUUM LEAK DETECTED (INSTANTANEOUS ACCUMULATION)

For a complete wiring diagramRefer to the Wiring Information.

  • When Monitored:

Ignition on and engine running with no MAP Sensor DTCs.

  • Set Condition:

The PCM detects that a large vacuum leak is present or that the signal voltage for both TP Sensors is stuck at 2.5 volts and calculated MAP is less than the Gas Flow Adaptation value. One trip fault will set within 5 seconds. ETC light will flash.

Possible Causes

INTERMITTENT DTC
VACUUM LEAK
MAP SENSOR CIRCUIT(S) OPEN, SHORTED, OR HIGH RESISTANCE
THROTTLE BODY CIRCUIT(S) OPEN, SHORTED, OR HIGH RESISTANCE
MAP SENSOR
THROTTLE BODY
POWERTRAIN CONTROL MODULE (PCM)

1.ACTIVE DTC

NOTE: / Diagnose and repair any TP Sensor or MAP Sensor DTCs before continuing.
NOTE: / This fault code could be present if any Cam/Crank DTCs are set. No repair is necessary for P2172 if any Cam or Crank DTCs are set.
NOTE: / Diagnose and repair any VSS or 5 Volt supply circuit DTCs before continuing.
NOTE: / The throttle plate and linkage should be free from binding and carbon build up.
NOTE: / Make sure the throttle plate is at the idle position.
1. / With the scan tool, select View DTCs and review the DTC environmental information.

Is the good trip counter greater than 0?
Yes

  • The DTC is not active at this time.

No

  • Go to2

2.VACUUM LEAK

NOTE: / This code is enabled to limit engine operation if a large vacuum leak should occur.
NOTE: / A large vacuum leak is the most probable cause of this DTC.
1. / Inspect the intake manifold, power brake booster, and PCV system for any vacuum leaks.
2. / Inspect the throttle plate. If the throttle blade is bent or will not close, the throttle body may need to be replaced.
3. / Inspect the MAP Sensor and Throttle Body for proper installation.
4. / Inspect the engine for any mechanical conditions that can cause improper engine vacuum.

Were any problems found?
Yes

  • Repair as necessary.

No

  • Go to3

3.MAP SENSOR OPERATION

1. / Start the engine.
2. / With a scan tool, monitor the MAP Sensor voltage.
3. / Snap the throttle.

Does the MAP Sensor voltage vary from below 2.0 volts at idle to above 3.5 volts at wide open throttle?
Yes

  • Go to5

No

  • Go to4

4.MAP SENSOR

1. / Turn the ignition off.
2. / Disconnect the MAP Sensor harness connector.
3. / Disconnect the PCM harness connector.
4. / Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the MAP Sensor and the Powertrain Control Module (PCM).
5. / Look for any chafed, pierced, pinched, or partially broken wires.
6. / Look for broken, bent, pushed out or corroded terminals.
7. / Check each of the MAP Sensor circuits for high resistance or a shorted condition.

Were any problems found?
Yes

  • Repair as necessary.

No

  • Replace the MAP Sensor.

5.THROTTLE FOLLOWER TEST

1. / Turn the ignition on.
2. / With a scan tool, perform the Throttle Follower Test and monitor the TP Sensor 1 and TP Sensor 2 voltages.
3. / Slowly press the throttle pedal down.
4. / The voltage for TP Sensor 1 should start at approximately 0.3 volts and increase to above 4.7 volts.
5. / The voltage for TP Sensor 2 should start at approximately 4.7 volts and decrease to approximately 0.3 volts.

Is the voltage within the range specified for each sensor?
Yes

  • Go to7

No

  • Go to6

6.THROTTLE BODY

1. / Turn the ignition off.
2. / Disconnect the Throttle Body harness connector.
3. / Disconnect the PCM harness connector.
4. / Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Throttle Body and the Powertrain Control Module (PCM).
5. / Look for any chafed, pierced, pinched, or partially broken wires.
6. / Look for broken, bent, pushed out or corroded terminals.
7. / Check each of the Throttle Body circuits for high resistance or a shorted condition.

Were any problems found?
Yes

  • Repair as necessary.

No

  • Replace the Throttle Body in accordance with the Service Information.

7.POWERTRAIN CONTROL MODULE (PCM)

1. / Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the MAP Sensor and the Powertrain Control Module (PCM) and between the Throttle Body and the Powertrain Control Module (PCM).
2. / Look for any chafed, pierced, pinched, or partially broken wires.
3. / Look for broken, bent, pushed out or corroded terminals.
4. / Refer to any Technical Service Bulletins that may apply.

Were any problems found?
Yes

  • Repair as necessary.
  • Perform the PCM Verification Test.

No

  • Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information.