Chrysler LLC - ME Building Group Construction Standards

Project & Bid Package Reviewed : Oct. 2010

SECTION 09982 – RESINOUS (EPOXY) FLOOR COATING

PART 1 - GENERAL

1.1  RELATED DOCUMENTS

Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division1 Specification Sections, apply to this Section.

1.2  SUMMARY

  1. This Section includes surface preparation and priming, and finish coats for floor coating.

1.3  SUBMITTALS

  1. Product Data: For each resinous floor coating system specified or intended for use.
  2. Material List: An inclusive list of required coating materials. Identify each material by manufacturer's catalog number and general classification.
  3. Manufacturer's Information: Manufacturer's technical information, including label analysis and instructions for handling, storing, and applying each coating material proposed for use.
  4. Certification: From the manufacturer attesting that products supplied comply with local regulations controlling use of volatile organic compounds (VOCs).
  5. Chrysler Vendor Code Numbers: Include Chrysler NPVP code number for all colors intended to be used.
  6. Samples for Selection: Submit manufacturer's color charts showing the full range of colors required.
  7. Installer Certificates: Signed by manufacturer certifying that installers comply with specified requirements.
  8. Material Certificates: For each resinous floor coating component, signed by manufacturer.
  9. Maintenance Data: For resinous floor coating to include in maintenance manuals.

1.4  QUALITY ASSURANCE

  1. Installer Qualifications: Engage an experienced installer (applicator) who is experienced in applying resinous floor coating systems similar in material, design, and extent to those indicated for this Project, whose work has resulted in applications with a record of successful in-service performance, and who is acceptable to resinous floor coating manufacturer.
  2. Engage an installer who employs only persons trained and approved by resinous floor coating flooring manufacturer for applying resinous floor coating systems indicated.
  3. Source Limitations: Obtain primary resinous floor coatings through one source from a single manufacturer. Provide secondary materials, including patching and fill material, joint sealant, and repair materials, of type and from source recommended by manufacturer of primary materials.
  4. Slip Resistance: Static coefficient of friction shall be 0.6 for level floors and 0.8 for ramped surfaces as defined by the ADA Accessibility Guidelines (ADAAG).
  5. Testing shall be in accordance with ASTM C1028 or use of similar devices recognized by ADAAG.

1.5  DELIVERY, STORAGE, AND HANDLING

  1. Deliver materials to the Project Site in manufacturer's original, unopened packages and containers bearing manufacturer's name and label, and the following information:
  2. Product name or title of material.
  3. Product description (generic classification or binder type).
  4. Manufacturer's stock number and date of manufacture.
  5. Contents by volume, for pigment and vehicle constituents.
  6. Thinning instructions.
  7. Application instructions.
  8. Color name and number.
  9. VOC content.
  10. Store materials not in use in tightly covered containers in a well-ventilated area at a minimum ambient temperature of 45degF. Maintain containers used in storage in a clean condition, free of foreign materials and residue.
  11. Protect from freezing.
  12. Keep storage area neat and orderly. Remove oily rags and waste daily. Take necessary measures to ensure that workers and work areas are protected from fire and health hazards resulting from handling, mixing, and application.

1.6  PROJECT CONDITIONS

  1. Environmental Limitations: Comply with resinous floor coating manufacturer's written instructions for substrate temperature, ambient temperature, moisture, ventilation, and other conditions affecting resinous floor coating application
  2. Close spaces to traffic during resinous floor coating application and for not less than 24 hours after application, unless manufacturer recommends a longer period.

PART 2 - PRODUCTS

2.1  MANUFACTURERS' REPRESENTATIVES

  1. ICI Paints World Group (ICI)
  2. Bob Benson, phone 248-853-0007
  3. Kevin Lastacy, phone 616-335-3259
  4. PPG Industries, Inc. (PPG)
  5. Ken Hartland, cell 248-521-6659
  6. Tom Orlando, cell 248-521-4751
  7. Tom Krynski, phone 313-417-9982
  8. Sherwin-Williams Company (S-W)
  9. Dick Gauthier, phone 248-541-3644 ext. 369; cell phone 248-830-0890
  10. Carl Sabo, phone 216-566-3034; fax 216-566-2775

2.2  RESINOUS FLOOR COATI NG MATERIALS

  1. Material Compatibility: Provide primers, undercoats, and finish-coat materials that are compatible with one another and the substrates indicated under conditions of service and application, as demonstrated by manufacturer based on testing and field experience.
  2. Full-Gloss Epoxy:
  3. Primer: Factory-formulated for use with full-gloss epoxy system. Apply at spreading rate recommended by manufacturer.
  4. Concrete Substrate: Provide primer as recommended by resinous floor coating manufacturer.
  5. Ferrous Metals: Provide primer as recommended by resinous floor coating manufacturer.
  6. Intermediate Coat: Unless otherwise directed by the manufacturer, provide the following applied at spreading rate recommended by manufacturer to achieve a dry film thickness of 2.0 to 5.0 mils per coat.
  7. Concrete Substrate:

1)  ICI: Tru-Glaze-WB 4408 Waterborne Epoxy Gloss Coating.

2)  PPG: 95-Series Aquapon 35 Polyamide-Epoxy Coating.

3)  S-W: Tile Clad II High Solids B62WZ Series B60VZ70.

  1. Ferrous Metals:

1)  ICI: Devflex #4208 Gloss.

2)  PPG: PittTech One Pack Int/Ext High-Performance Waterborne High-Gloss DTM Industrial Enamels 90-374 Series.

3)  S-W: DTM Acrylic Gloss Coating, B66100.

  1. Finish Coat: High-gloss epoxy applied at spreading rate recommended by manufacturer to achieve a dry film thickness of 2.0 to 5.0 mils, per coat.

1)  ICI Dulux Paints: Tru-Glaze-WB 4408 Waterborne Epoxy Gloss Coating.

2)  PPG: 95-Series Aquapon 35 Polyamide-Epoxy Coating.

3)  S-W: Tile Clad II High Solids B62WZ Series B60VZ70.

2.3  COLORS

  1. Provide the following NPM Code colors complying with Chrysler Standards for areas being marked, as verified by the Owner's Representative
  2. White NPVP 9.5
  3. Safety Yellow NPVP 3.75Y 8.5/12
  4. Safety Red NPVP 7.5R 4/14
  5. Corporate Blue NPVP 6.8PB1.85/12.4

2.4  ACCESSORY MATERIALS

  1. Patching and Fill Material: Resinous product of or approved by resinous floor coating manufacturer and recommended by manufacturer for application indicated.
  2. Joint Sealant: Type recommended or produced by resinous floor coating manufacturer for type of service and joint condition indicated.

PART 3 - EXECUTION

3.1  EXAMINATION

  1. Examine substrates, areas, and conditions, with the Applicator present, under which resinous floor coating will be performed for compliance with resinous floor coating application requirements.
  2. Do not begin to apply resinous floor coating until unsatisfactory conditions have been corrected and surfaces receiving resinous floor coating are thoroughly dry.
  3. Start of resinous floor coating will be construed as the Applicator's acceptance of surfaces and conditions within a particular area.

3.2  PREPARATION

  1. Cleaning: Before applying resinous floor coating or other surface treatments, clean the substrates of substances that could impair the bond of the various coatings. Remove oil and grease before cleaning. Schedule cleaning and resinous floor coating so dust and other contaminants from the cleaning process will not fall on wet, newly coated surfaces.
  2. Surface Preparation: Clean and prepare surfaces to be coated according to manufacturer's written instructions for each particular substrate condition and as specified.
  3. Provide barrier coats over incompatible primers or remove and reprime.
  4. Concrete: Remove glaze, chalk, dust, dirt, grease, oils, and release agents. If curing compounds, hardeners or sealers have been used to improve curing, use mechanical methods of surface preparation.
  5. Shot-blast surfaces with an apparatus that abrades the concrete surface, contains the dispensed shot within the apparatus, and recirculates the shot by vacuum pickup.
  6. Surface texture shall be similar to 100 grit sandpaper.
  7. Determine alkalinity and moisture content of surfaces by performing appropriate tests. If surfaces are sufficiently alkaline to cause the finish resinous floor coating to blister and burn, correct this condition before application. Do not coat surfaces where moisture content exceeds that permitted in manufacturer's written instructions.
  8. Ferrous Metals: Clean ungalvanized ferrous-metal surfaces that have not been shop coated; remove oil, grease, dirt, loose mill scale, and other foreign substances. Use solvent or mechanical cleaning methods that comply with the Steel Structures Painting Council's (SSPC) recommendations.
  9. Touch up bare areas and shop-applied prime coats that have been damaged. Wire-brush, clean with solvents recommended by resinous floor coating manufacturer, and touch up with the same primer as the shop coat.
  10. Materials Preparation: Mix and prepare resinous floor coating materials according to manufacturer's written instructions.
  11. Maintain containers used in mixing and applying resinous floor coating in a clean condition, free of foreign materials and residue.
  12. Stir material before application to produce a mixture of uniform density. Stir as required during application. Do not stir surface film into material. If necessary, remove surface film and strain material before using.
  13. Use only thinners approved by resinous floor coating manufacturer and only within recommended limits.
  14. Use patching and fill material to fill holes and depressions in substrates according to manufacturer's written instructions.
  15. Treat control joints and other nonmoving substrate cracks to prevent cracks from reflecting through resinous flooring according to manufacturer's written recommendations.

3.3  APPLICATION

  1. General: Apply resinous floor coating according to manufacturer's written instructions. Use applicators and techniques best suited for substrate and type of material being applied.
  2. Resinous floor coating colors, surface treatments, and finishes are indicated in the schedules.
  3. Do not coat over dirt, rust, scale, grease, moisture, scuffed surfaces, or conditions detrimental to formation of a durable resinous floor coating film.
  4. Provide finish coats that are compatible with primers used.
  5. Application Procedures: Apply resinous floor coatings by brush, roller, spray, or other applicators according to manufacturer's written instructions.
  6. Brushes: Use brushes best suited for the type of material applied. Use brush of appropriate size for the surface or item being coated.
  7. Rollers: Use rollers of carpet, velvet back, or high-pile sheep's wool as recommended by the manufacturer for the material and texture required.
  8. Spray Equipment: Use airless spray equipment with orifice size as recommended by the manufacturer for the material and texture required.
  9. Minimum Thickness: Apply resinous floor coating materials no thinner than manufacturer's recommended spreading rate. Provide the total dry film thickness of the entire system as recommended by the manufacturer.
  10. Prime Coats: Before applying finish coats, apply a prime coat of material, as recommended by the manufacturer, to material that is required to be coated or finished and that has not been prime coated by others. Recoat primed and sealed surfaces where evidence of suction spots or unsealed areas in first coat appears, to ensure a finish coat with no burn through or other defects due to insufficient sealing.
  11. Finishes: Completely cover surfaces as necessary to provide a smooth, opaque surface of uniform finish, color, appearance, and coverage. Cloudiness, spotting, holidays, laps, brush marks, runs, sags, ropiness, or other surface imperfections will not be acceptable.
  12. Completed Work: Match approved samples for color, texture, and coverage. Remove, refinish, or recoat work not complying with requirements.

3.4  PROTECTION AND CLEANING

  1. Protect adjacent surfaces from over spray or splattering. Correct damage by cleaning, repairing or replacing, and recoating, as approved by Owner’s Representative.
  2. Provide "Wet Paint" signs to protect newly coated finishes. Remove temporary protective wrappings provided by others to protect their work after completing coating operations.
  3. Cleanup: At the end of each workday, remove empty cans, rags, rubbish, and other discarded resinous floor coating materials from the site.
  4. After completing coating, clean resinous floor coating-spattered surfaces. Remove spattered resinous floor coating by washing and scraping. Be careful not to scratch or damage adjacent finished surfaces.

END OF SECTION

RESINOUS (EPOXY) FLOOR COATING 09982 - 2 of 5