SECTION 11 52 13.13
ACCESS MULTIVIEW/SERIES E FRONT PROJECTION SCREENS
** NOTE TO SPECIFIER ** Draper Inc; Ceiling recessed front projection screens.
.
This section is based on the products of Draper, Inc., which is located at:
411 S. Pearl Street
Spiceland, IN 47385
Tel: (800) 238-7999
Fax: (765)987-7142
www.draperinc.com
Draper manufactures the best and most complete line of projection screens in the world. We want to help you incorporate these screens into the most effective presentation systems. Planning a projection system involves several steps: choosing the screen size, viewing surface, screen model and control system if required. For additional information, see Draper Screen Selection/Resource Center at www.draperinc.com.
PART 1 GENERAL
1.1 SECTION INCLUDES
A. Electrically operated, ceiling recessed, front projection screens.
1.2 RELATED SECTIONS
** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.
A. Division 5 - Metal Fabrications: Suspension systems for projection screens.
B. Section 06 40 00 - Architectural Woodwork: Wood trim for recessed screen installation.
C. Section 09 22 26 - Suspension Systems: Supports and trim for suspended ceilings.
D. Section 09 23 00 - Gypsum Plastering: Ceiling for recessed screen installation.
E. Section 09 21 16 - Gypsum Board Assemblies: Ceiling for recessed screen installation.
F. Section 09 51 00 - Acoustical Ceilings: Ceiling for recessed screen installation.
G. Division 16 for electrical wiring, connections, and installation of remote control switches for electrically operated projection screens.
1.3 SUBMITTALS
A. Submit under provisions of Section 01 30 00.
B. [ Product Data ]: Manufacturer's data sheets on each product to be used, including:
1. Preparation instructions and recommendations.
2. Storage and handling requirements and recommendations.
3. Installation methods.
C. Wiring diagram for electrically operated units.
** NOTE TO SPECIFIER ** Retain below for front projection screens where shop drawings are needed to understand relationships with adjoining work.
D. Shop Drawings: Shop drawings showing layout and types of projection screens. Show the following:
** NOTE TO SPECIFIER ** Edit below to suit screens specified and project conditions.
1. Location of screen centerline.
2. Location of wiring connections.
3. Seams in viewing surfaces.
4. Detailed drawings for concealed mounting.
5. Connections to suspension systems.
6. Anchorage details.
7. Accessories.
8. Frame details.
** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.
E. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.
F. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.
1.4 QUALITY ASSURANCE
A. Single Source Responsibility: Obtain each type of projection screen required from a single manufacturer as a complete unit, including necessary mounting hardware and accessories.
B. Coordination of Work: Coordinate layout and installation of projection screens with other construction supported by, or penetrating through, ceilings, including light fixtures, HVAC equipment, fire-suppression system, and partitions.
1.5 DELIVERY, STORAGE, AND HANDLING
A. Do not deliver projection screens until building is enclosed and other construction where screens will be installed is substantially complete.
B. Store products in manufacturer's unopened packaging until ready for installation.
C. Protect screens from damage during delivery, handling, storage, and installation.
1.6 COORDINATION
A. Coordinate work with installation of ceilings, walls, electric service power characteristics, and location.
PART 2 PRODUCTS
2.1 MANUFACTURERS
A. Acceptable Manufacturer: Draper, Inc., which is located at: 411 S. Pearl P. O. Box 425 ; Spiceland, IN 47385-0425; Toll Free Tel: 800-238-7999; Tel: 765-987-7999; Email: ; Web: www.draperinc.com
** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.
B. Substitutions: Not permitted.
C. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00.
2.2 MOTORIZED, CEILING RECESSED, FRONT PROJECTION SCREENS
A. Access MultiView/Series E: Electric motor operated, extruded aluminum case, independently motorized masking. Ceiling-recessed, extruded aluminum headbox and extruded aluminum housing. UL approved "Suitable for use in environmental air space." Bottom closure panel forms slot for passage of viewing surface and is removable for access to operating mechanism and viewing surface. Bottom perimeter flange provides support and trim for acoustical ceiling panels or for trim for gypsum board ceilings. The case may be ordered in advance and the screen installed later to eliminate field damage. The screen installs in minutes. Housing is symmetrical allowing for left and right hand motor locations and for viewing surface to unroll off front or back of roller. Housing designed with internal junction box and plug-in wiring connections to allow housing to be installed and connected to building power supply separately from motor and viewing surface.
** NOTE TO SPECIFIER ** Select one of the following four motor paragraphs and delete the paragraphs not required. Note that there are size limitations with quiet motors. Contact manufacturer for additional information.
1. Motor mounted inside screen roller on rubber isolation insulators. Motor UL certified, rated 110-120V AC, 60 Hz, three wire, instantly reversible, lifetime lubricated with pre-set accessible limit switches. Motor with overload protection and electric brake.
2. Motor Screen Controls, UL certified.
** NOTE TO SPECIFIER ** Not compatible with options b, c, or d.
a. Single station control rated 115V AC, 60 Hz with two 3-position rocker switches with cover plate to stop or reverse screen and masking at any point.
b. Access MultiView Control Wall Switch. Low voltage control allows both motors to be controlled by independent 3-button switches in a single box)
c. Wireless Remote Control: Two multi-channel Infrared Controls, two receivers and one transmitter.
d. Low Voltage Wall Switch AND Wireless Control: IGC/3N1, two wall switches with built-in infrared receivers and one transmitter.
3. Projection Viewing Surface:
** NOTE TO SPECIFIER ** Select the screen type and delete two of the following three paragraphs.
a. Matt white, washable surface. For use with any type projector where light can be controlled. GREENGUARD for Children and Schools certified.
b. Glass beaded, textile backed. Best for use with table mounted projectors. Flame and mildew resistant.
c. Grey projection surface, High Contrast Grey. Provides a greater contrast and black reproduction than standard surfaces. Allows for more ambient light in the audience area than traditional surfaces. Available in sizes through 8 feet high (2.44 m). GREENGUARD for Children and Schools certified.
d. Acoustically Transparent AT1200, Flame and mildew resistant. Suitable for installations where speakers are located behind projection screen. White in color. Available in sizes through 6 feet high (1.83 m).
e. Acoustically Transparent AT Grey. Flame and mildew resistant. Suitable for installations where speakers are located behind projection screen. Grey in color. Available in sizes through 6 feet high (1.83 m).
** NOTE TO SPECIFIER ** Select the screen format and size required for the project. Delete the paragraphs not required.
4. Viewing Area H x W.
a. HDTV (16:9) to NTSC (4:3) Format. Black masking borders standard.
1) 92 inch (2337 mm) diagonal, 45 inches x 80 inches (1143 mm x 2032 mm).
2) 106 inch (2692 mm) diagonal, 52 inches x 92 inches (1321 mm x 2337 mm).
3) 123 inch (3124 mm) diagonal, 60 inches x 107 inches (1524 mm x 2718 mm).
4) 133 inch (3378 mm) diagonal, 65 inches x 116 inches (1651 mm x 2946 mm).
b. WideScreen (1.85:1) to NTSC Format (4:3). Black masking borders standard.
1) 95 inch (2413 mm) diagonal, 45 inches x 83 inches (1143 mm x 2108 mm).
2) 109 inch (2769 mm) diagonal, 52 inches x 96 inches (1321 mm x 2438 mm).
3) 126 inch (3200 mm) diagonal, 60 inches x 111 inches (1524 mm x 2819 mm).
4) 136 inch (3554 mm) diagonal, 65 inches x 120 inches (1651 mm x 3048 mm).
c. CinemaScope (2.35:1) to HDTV Format (16:9). Black masking borders standard.
1) 103 inch (2616 mm) diagonal, 40-1/2 inches x 90-1/4 inches (1029 mm x 2292 mm).
2) 115 inch (2921 mm) diagonal, 45 inches x 105-3/4 inches (1143 mm x 2686 mm).
3) 132 inch (3353 mm) diagonal, 52 inches x 122 inches (1321 mm x 3099 mm).
** NOTE TO SPECIFIER ** Edit the following if an extra screen drop exceeding the standard of 12 inches (305 mm) is required for the project. Black is standard for all formats. Note that extra drop will increase the overall length of the case. Select the screen drop type and fill in the drop height from one of the following paragraphs and delete the other. Total screen height cannot exceed 12 feet (3.66 m). If extra screen drop is not required, delete both paragraphs.
5. Provide an extra screen drop with an overall screen drop of ___ feet (___ m) with top border matching viewing surface color.
6. Provide an extra screen drop with an overall screen drop of ___ feet (___ m) with a black masking top border.
PART 3 EXECUTION
3.1 EXAMINATION
A. Do not begin installation until substrates have been properly prepared.
B. Verify rough-in openings are properly prepared.
C. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
3.2 PREPARATION
A. Clean surfaces thoroughly prior to installation.
B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
3.3 INSTALLATION
A. Install in accordance with manufacturer's instructions.
B. Install front projection screens with screen cases in position and relationship to adjoining construction as indicated, securely anchored to supporting substrate, and in manner that produces a smoothly operating screen with plumb and straight vertical edges and plumb and flat viewing surfaces when screen is lowered.
C. Test electrically operated units to verify that screen, controls, limit switches, closure and other operating components are in optimum functioning condition.
3.4 PROTECTION
A. Protect installed products until completion of project.
B. Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION
11131-1